NVIDIA GeForce GTX 750 Ti - rozlišení obrazovky
Moderátoři: Pic, Mods_junior, Mods_senior, HW spec team
-
Uziv00
Re: NVIDIA GeForce GTX 750 Ti - rozlišení obrazovky
A co nepoužít nvidii a zkusit to normálně ve windows? "Zobrazit všechny režimy"?
-
d1amond
- člen HW spec týmu
- Příspěvky: 16119
- Registrován: 26 kvě 2008 10:14
- Bydliště: České Budějovice
Re: NVIDIA GeForce GTX 750 Ti - rozlišení obrazovky
To určitě používá, pokud má v DVI zapojený VGA kabel.
Nikdy neříkej, že to nejde, protože se najde někdo, kdo o tom neví a udělá to!
Chcete si nechat sestavit nový počítač?
Chcete si nechat sestavit nový počítač?
-
Martin12222
- nováček
- Příspěvky: 11
- Registrován: 03 led 2014 12:17
Re: NVIDIA GeForce GTX 750 Ti - rozlišení obrazovky
Problém vyřešen.. Vytvořil jsem si nové rozlišení s parametry 1440x900 podle jednoho návodu.
z nVidia fora:
1. NVIDIA Control Panel > Display > Manage custom timings.
2. Click both "Treat as HDTV" and "Allow modes not exposed by the display"
3. Click [Create...]
4. Under Custom display mode values:
Horizontal desktop pixels: 1440
Vertical desktop lines: 900
GDI Refresh rate: 60
Bits per pixel: 32
(don't have "Interlaced" checked)
5. Click [Advanced >>] (by the way this is where I didn't go when NVIDIA emailed me)
6. Under "Back-end parameters":
Timing standard: DMT
Desired refresh rate: 60
(the rest of the fields are grayed out)
7. Under "Front-end paramers"
Scaling type: Display (none)
8. Click [Test]
9. Click [OK]
Děkuji všem za vaše nápady a pomoc.
z nVidia fora:
1. NVIDIA Control Panel > Display > Manage custom timings.
2. Click both "Treat as HDTV" and "Allow modes not exposed by the display"
3. Click [Create...]
4. Under Custom display mode values:
Horizontal desktop pixels: 1440
Vertical desktop lines: 900
GDI Refresh rate: 60
Bits per pixel: 32
(don't have "Interlaced" checked)
5. Click [Advanced >>] (by the way this is where I didn't go when NVIDIA emailed me)
6. Under "Back-end parameters":
Timing standard: DMT
Desired refresh rate: 60
(the rest of the fields are grayed out)
7. Under "Front-end paramers"
Scaling type: Display (none)
8. Click [Test]
9. Click [OK]
Děkuji všem za vaše nápady a pomoc.
-
- Podobná témata
- Odpovědi
- Zobrazení
- Poslední příspěvek
-
- 0 Odpovědi
- 7631 Zobrazení
-
Poslední příspěvek od Vítek Pokorný
-
- 1 Odpovědi
- 12272 Zobrazení
-
Poslední příspěvek od Kogaku
-
- 1 Odpovědi
- 4298 Zobrazení
-
Poslední příspěvek od rhsCZ
-
- 0 Odpovědi
- 18597 Zobrazení
-
Poslední příspěvek od Emzi
-
- 2 Odpovědi
- 3510 Zobrazení
-
Poslední příspěvek od petr22
